[ Pobierz całość w formacie PDF ]

technopolymer.
a$ the stock steel plate.
Both spacer `$ and plate a$ are designed to secure two different drops, each with
a cast-off or a cast-on (for left-handed shooters) depending on how they are
assembled. Other stock drop values can be obtained using the set of spacers
supplied.
REMOVING THE GEL" TEK RECOIL PAD
VERSION WITH STANDARD STOCK
" Using a flathead screwdriver (approx. 4 mm/0.2 ), pull out the retaining clasp
of the Gel" Tek recoil pad (Fig. 41).
" Remove the Gel" Tek recoil pad (Fig. 42).
For the Beretta break-open semiautomatic UGB25 Xcel with multi-adjustable
stock, remove the recoil pad assembly as described in the section entitled
 ADJUSTING THE MULTI-ADJUSTABLE STOCK .
REPLACING THE SPACER AND PLATE
NOTICE: The  DX mark on the spacer and on the plate means  cast-off , the
 SX mark means  cast-on . The stock drop values are expressed in millimeters.
The stock drop and cast of the spacer `$ must always correspond to those of the
metal plate a$.
NOTICE: The stock drop and cast modification must be carried out by a competent
gunsmith.
NOTICE: It is advisable to carry out the following operations over a table to catch
components should they drop.
60
Tools required:
" Screwdriver.
" Hexagonal spanner (6 mm).
" Torque wrench (suggested) with a 6-mm pipe extension.
MODIFYING THE STOCK DROP AND CAST
" Disassemble
the stock
using the
`$
hexagonal
spanner and
remove the spacer
and the plate.
" Position the spacer `$ around
the stock bolt tube. Make sure that the
marking showing the desired drop and cast
a$
( C-60-SX in the drawing) is visible on the
spacer.
" Put the rear plate a$ and the spring washer in
the stock insert until the plate reaches its seat
in the stock. Make sure that the same marking
referring to the drop and cast ( C-60-SX in the drawing)
is visible on the plate.
" Use the screwdriver to center the plate and the washer in the
stock.
" Assemble the stock, making sure to locate the stock bolt tube through
the rear plate a$ and the washer. Also make sure that the front spacer `$
is centered between the stock and the receiver. (During this operation keep
the shotgun vertical with the barrel down).
" Using the hexagonal spanner insert the stock retaining nut with a torque of
about 1.6/1.8 Kgm (11.6/13.0 Ftlb) (Kg meter). A torque wrench is useful for
this purpose.
" Reassemble the recoil pad.
REASSEMBLING THE GEL" TEK RECOIL PAD
VERSION WITH STANDARD STOCK
" Using a flathead screwdriver (approx. 4 mm/0.2 ), pull out the retaining clasp
of the Gel" Tek recoil pad (Fig. 42).
" Place the pad on the stock and make sure that all bushings are placed in the
proper holes.
" Pushing the pad securely against the stock, push retaining clasp upwards, until
it disappears in the pad assembly. Be sure that the pad fits flush and firmly to
the stock (Fig. 43).
For the Beretta break-open semiautomatic UGB25 Xcel with multi-adjustable
stock, remount the recoil pad assembly following the instructions provided in the
section entitled:  ADJUSTING THE MULTI-ADJUSTABLE STOCK .
61
REVERSIBLE SAFETY
CAUTION: This operation must be carried out by a competent gunsmith.
WARNING: Check that the gun is unloaded (empty cartridge chamber and carrier).
!
If necessary, unload the gun as described in the relevant section.
WARNING: Never point the gun at someone or at a hard or flat surfaces. Always
!
treat the gun as if it were loaded. (See points 1, 2 and 4 of the BASIC SAFETY
RULES).
NOTICE: It is advisable to carry out the following operations over a table to catch
components should they drop.
The safety button is factory assembled to be engaged by pushing it from the left
to the right side of the receiver and disengaged in the opposite direction with the
index finger of the right hand (right-handed shooters).
To ensure the same easy handling for left-handed shooters, the safety can be
mounted in a reverse position so that it can be engaged from the right to the left
side of the gun and disengaged in the opposite way by using the left index finger.
Proceed as follows to assemble the safety in a reverse position:
" Cock the hammer by levering the barrel downwards.
" Keep the safety plunger pressed down with a drift punch and push the safety
out of its seat (from the right to the left side of the gun).
CAUTION: Take care to prevent the plunger spring from coming out of its seat
together with the plunger as they may get lost.
Mount the safety in the reverse position from the left to the right side of the gun
and push the safety button in position while keeping the safety plunger pressed
down.
INTERCHANGEABLE TOP RIB
WARNING: Check that the gun is unloaded (empty cartridge chamber and carrier).
!
If necessary, unload the gun as described in the relevant section.
WARNING: Never point the gun at someone or at a hard or flat surfaces. Always
!
treat the gun as if it were loaded. (See points 1, 2 and 4 of the BASIC SAFETY
RULES).
NOTICE: It is advisable to carry out the following operations over a table to catch
components should they drop.
NOTICE: It is advisable to remove the barrel.
62
DISASSEMBLING THE TOP RIB
" Remove the rib retaining pin using a tip punch (Fig. 44).
" Push the rib toward the muzzle, raise it and remove it from the barrel.
REASSEMBLING THE TOP RIB
Note the following:
" Position the front rib lug in the grooves on the barrel. Keep the rib parallel with
the barrel and protruding by approx. 2 cm from the muzzle. The rib lug must
be inserted first by the front side of the groove (arrow A Fig. 45).
" Position the rib center lugs in the barrel/fore-end spacers (Fig. 46) and the rear
of the rib in the T-slot (Fig. 47) on the barrel extension.
NOTICE: During these operations, the top rib must be firmly kept in contact with
the barrel surface to allow the top rib retaining points to fit snugly in the relevant
seats on the barrel.
" When the top rib retaining points are well fitted in their seats on the barrel, slide
the top rib along the barrel so that it perfectly engages the front rib lug in the
dovetailed seat of the barrel groove (arrow B Fig. 45). [ Pobierz całość w formacie PDF ]

zanotowane.pl

doc.pisz.pl

pdf.pisz.pl

razem.keep.pl